Отделение ускорительного комплекса
  • Главная
    • Описание ускорительного комплекса
    • Работа ускорительного комплекса
    • Описание системы управления
    • Администрация и сотрудники
    • История в фотографиях
Информация о материале
Просмотров: 165

Bibliography for the Theme

Artemov A.D., Balbekov V.I, Belov V.I. et.al.
The Fast Booster-Injector of IHEP Proton Synchrotron.
- Proceeding on 2th National Conference of Charged Particulars Accelerators, Dubna, 1972, vol.1, p.71.

Ado Ju.M., Balbekov V.I., Myae E.A. et.al.
The Ring IHEP Injector.
- Proceeding on 5th National Conference of Charged Particulars Accelerators, Moscow, 1977, vol.1, p.42.

Vasiljev E.A., Brook V.L., Glukhih L.A. et.al.
The basic results of complex adjustment and physical start-up the Booster Proton Synchrotron on energy 1,5 Gev - IHEP Booster.
- Proceeding on 9th National Conference of Charged Particulars Accelerators, Dubna, 1985, vol.1, p.14.

Информация о материале
Просмотров: 3702

Режим прикладных исследований при работе в составе ускорительного комплекса

 

Режим межпакетного программирования

 Для повышения эффективности использования бустера в прикладных исследованиях был создан режим межпакетного программирования (МПП) параметров систем вывода и транспортировки. Он реализуется на основе программирования от пакета к пакету величины поля вывода, токов питания выводных устройств и магнитооптических элементов прямой ветви канала. Программируются также задержки, синхронизирующие включение систем относительно основных таймерных импульсов.

Режим МПП позволяет в течение коротких остановок основного ускорителя вести облучение экспериментальной установки и оперативно за один суперцикл возвращаться к исходным условиям инжекции пучка в У-70.

Режим внутрипакетного программирования

Кроме того, отработан режим внутрипакетного программирования (ВПП). Он создает возможность в тех случаях, когда У-70 не потребляет максимальной интенсивности, то есть используется не весь пакет импульсов, выводить пучок в оставшихся импульсах на экспериментальную установку. При этом количество импульсов, величина интенсивности в них, уровень энергии выводимых частиц и длительность сгустка программируются.

К особенностям режима ВПП следует отнести “мертвое время” в пакете, необходимое для спадания тока в разводящем поворотном магните при его выключении. В это время все системы бустера работают, но пучок из линейного ускорителя не инжектируется, и в трех циклах пучок отсутствует.

Режим внутрипакетного программирования снижает стоимость прикладных исследований и обеспечивает высокую эффективность их проведения. Период времени, доступный для выполнения экспериментов, становится сравнимым с длительностью сеанса работы ускорительного комплекса (~3000 часов в год). При этом имеется возможность вести исследования только в устойчивых режимах работы бустера с наилучшей повторяемостью параметров пучка от цикла к циклу.

Информация о материале
Просмотров: 87

Train-to-train modulation mode 

This mode is employed to increase efficiency of running the Booster for applied-research purposes. Parameters of beam ejection and beam transport systems are programmed on a train-to-train basis. Subjects to programming are the ejection field level, amplitude of pulses to power extraction equipment and transfer line optics in the transport line onto beam absorber, and delays to trigger sub-systems with respect to the based timing signals.

The train-to-train modulation mode allows for irradiating the experimental samples during short stops of the main accelerator and re-entering readily the routine injection-to-U-70 mode, when required.

Pulse-to-pulse modulation mode

 This mode is used when the U-70 does not demand for the top intensity and accepts only a few pulses of a train. In this case, the unused beam pulses are directed towards the experimental set-up. Subjects to programming are the number of pulses, their intensity, energy of extracted beam, and bunch-length.

In this mode, there is a certain dead period (three pulses in a train) required by field in the beam-line switch dipole magnet to die out. During this period, all the Booster systems are operating, but there is no beam injection from the linac.

Use of the mode in question saves the cost of applied programs and improves their efficiency. Indeed, to the final end, period of beam availability to experiments turns out to be commensurable to the run time of the entire complex, about 3,000 hours per year. All the more, there creates a possibility of performing applied programs under the stable operational conditions of the Booster with the best cycle-to-cycle reproducibility of beam parameters.

Информация о материале
Просмотров: 361

The Booster accepts 30 MeV protons injected from the linear accelerator URAL-30 that yields beam pulses of 10 ms length. Their current is adjustable within a 30–70 mA range. Horizontal and vertical emittances of beam at exit from the URAL-30 are both equal to 40p mm

xmrad (at 95% level). Momentum spread of injected beam is ±3,0x10-3.

Beam injection scheme

Beam injection into the Booster is accomplished with four pulsed magnets UBM1–UBM4 and septum magnet SM1. Intensity of the accelerated beam depends upon the injection scheme implemented. There are 1-, 2-, 3- and 4-turn injection schemes available by now. One-turn rotation period is 1,34 ms. During the multi-turn injection process, effective horizontal emittance of the accumulated beam increases to 40p cmx

mrad. Beam brightness can be tuned by varying both, average current from the URAL-30 and number of injection turns.

Acceleration

On injection, the beam is uniform and occupies the entire ring. Then, the beam is captured into a single RF bucket, and longitudinal size of the bunch shrinks with beam energy increasing. To this end, in a routine operation mode with 1.32 GeV top energy, the bunch would occupy 22% of the orbit circumference. It corresponds to bunch length of 80 ns and momentum spread of ±2,7x10-3. By varying amplitude across RF accelerating cavities, one can lengthen the ejected bunch to about 160 ns with its momentum spread being reduced to Dр/р=±1,3x10-3.

Beam ejection scheme

Beam ejection from the Booster is accomplished with the three bump magnets BM1-BM3, septum magnet SM2 and pulsed kicker magnet UM1. Trigger to fire UM1 is synchronized to phase of accelerating RF voltage so as to lock the 100 ns long front of the pulsed current to the beam gap.

Energy of ejected beam can be varied in a wide, 200–1320 MeV range. Feasible value of energy discreteness is dictated by accuracy available of magnetic field measurements throughout the acceleration cycle. The guide field is measured with a probe based on electron paramagnetic resonance effect and analog integrator able to resolve a 5 Gs field increment. Thus, the attainable fractional error of beam energy at extraction does not exceed 2,4x10-3 at lower and 5,9x10-4 at higher energies.

Given emittances of 20p mmxmrad horizontally and 10p mmxmrad vertically, beam spot size amounts to around ~4x

4 cm2 upstream of the experimental zone. It can be varied through retuning the beam transfer line optics and depends on position of a sample to be irradiated. Position of the beam center can be steered with dipole corrector magnets.

Delicate operation options

There exists a possibility to run the Booster in optional modes that might be requested for a delicate applied study. Namely,

By applying to shortened pulses that power injection bump magnets in a 1-turn injection scheme, one can accumulate and accelerate up to 3,0x1011 protons per a cycle. Adding the second RF harmonic to the accelerating field may be used to decrease momentum spread of the beam, say, to ±5,0x10-4 at energy 1.32 GeV.
Beam ejection with longitudinal emittances as small as 0.1–0.45 eVs is feasible. It can be achieved, at the expense of an increased beam loss, via imposing the RF voltage program with lower amplitudes throughout the cycle.

To improve accuracy of beam parameter diagnostics, beam extraction procedure can be accompanied by issuing a protocol containing rotation frequency and beam orbit data, both measured at 10-20 ms prior to kick-out. Thus, beam energy can be monitored with an accuracy better than 10-3.

Информация о материале
Просмотров: 3021

В 1998 г. начата проработка вопросов использования тоннеля для задач физики высоких энергий и космических лучей.

Одним из вариантов использования тоннеля УНК является размещение нейтринного детектора для изучения осцилляций нейтрино. Источником этих нейтрино могут быть ускорительные установки в Японии (JHF), Германии (GSI) или США (MI).

  1. Итог выполнения программы УНК
  2. Краткая история программы УНК
  3. Bibliography for the Theme
  4. Краткий список основных публикаций об УНК

Страница 6 из 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10